SPI-K71 档位指示器套件 ZRX 1200 R 01-03 専用
商品 # 11071
商品 # 11071
※车型适用资讯以该车辆原厂配置为准,若改装齿盘、摇臂等请自行评估需要的目数、规格。
※安装需要专用工具。
Fits: KAWASAKI ZRX1100 97-00, KAWASAKI ZRX1200R 01-03
With the replacement of the brake disc, I put the magnet back on. 5mm RubberWasher I glued it together with a good fitView Detail
Fits: KAWASAKI ZRX1100 97-00, KAWASAKI ZRX1200R 01-03
It is a good thing without it, but when you try to put it on, the surface is white It was the Front specification, but because I didn't like the Front, I made my own Bracket I did some work, such as extending the wiring, and installed it in the rear It is unreliable When I pushed the Wiring in recently, the Plus power wire came loose from the Coupler Repairs were done to attach the solder to the coupler terminalsView Detail
Fits: KAWASAKI ZRX1100 97-00, KAWASAKI ZRX1200R 01-03
I installed it in the ZrX 1100.
Installation was easy to install just by Wiring as Instruction Manual.
Since there is a deviation in the setting as it is, it can be used without problems by doing the setup again.
With this, the vision 6th gear is gone.
View Detail
Fits: KAWASAKI ZRX1100 97-00, KAWASAKI ZRX1200R 01-03
It installed in the reverse car of ZrX 1200 R in 2001. Since attachment comes with a dedicated Harness, it breaks into Meter's 110 type 3-pole Coupler and the NeutralMinus line is set to Meter's 110 type 9 pole Coupler line's young grass color (A sky-blue line connected to Meter's Neutral lamp) By interrupting with Electro Tap and connecting with the PG - 110 Magnetic Sensor attached by connecting with Haritometry made by KITACO 's 110 type 9 - pole Coupler in the Instruction Manual, the Wiring work is over.
For installation of Magnetic Sensor, paste Magnet on Disc Lock, jointly tighten Exclusive Bracket to Caliper bolt, set Sensor and set the gap between Magnet and Sensor to about 4 mm. If this interval is too large, the reaction will be slow Be careful as it will no longer react, at all.
I tried to connect using DAYTONA's electric type SpeedometerConversion AdapterTwin type without using the PG-110 Magnetic Sensor, but after putting it in the low, I put it in Second, but because I did not have a reaction, I made it a challenge. Perhaps it may be used depending on the setting, but please let me know if you can do it.
And also paint on SensorBracket is too weak spraying Parts cleaner All paint has been peeled off since we turned to painting but it is a place I want you to Minor change on Manufacturer side It is finished with Anodized etc. It is installed near Brake Caliper To be dirty in the place where you are dirty with Bracket I think that the painting is bad with the Cleaner Besides, since the shape of the Bracket is not good and it rubs against the Outer of the Front fork, it is a little cut off the corner of the Bracket did.
After having troubled installing the critical Indicator, we made a dedicated Bracket a little on the top of the Meter and installed it together with the ETCIndicator It is a good feeling to Refreshing because I put the Indicator on the floor so that Wiring can not be seen.
It is quite easy to use and it shows quite good performance as expected. Since it was a 5-speed car, I was going to put it in 6th speed immediately on a highway so I can do it with my 6th speed of illusion as well.
It is a recommended item for those who want to enter the 6th speed with Parts that I want to ride again with.View Detail
Fits: KAWASAKI ZRX1100 97-00, KAWASAKI ZRX1200R 01-03
Purchase for friends ZrX 1100. products are "ZrX1200R 01-03 exclusive use" Although it is the same as ZrX 1100 and MeterWiring, the kit can be used as it is. However, since the GEAR ratio is different from 1200, it is necessary to reset by actual driving after resetting.
Reset needs hang. When it is pushed slowly three times, it is not reset and it is comparatively slow "Cha Chica Chi Chi" And it should be done three consecutive times.
Also, I fixed the installation Bracket to Caliper Mount Bolt with the same, but it is difficult to manage Torque management by turning around. If you put Stainless washer between Bracket and Bolt it will be hard to turn around.
This Kit, Interruption Harness is only 3PCoupler, Neutral signal is designed to interrupt on Neutral line of 6PCoupler with Electro Tap. Because I did not want to hurt OEMWiring, I bought DAYTONA's 110 type 6PC coupler kit and made an interrupt Harness separately.View Detail
如要继续浏览此商品,请点击"前往Webike日本站",将引导您去Webike日本站(日文)继续浏览此商品。
通知
在您加入购物车前请选择选项。