'.在一个小围栏内对每个气缸进行燃料控制
。此外,还可以增加一个额外的2位置地图切换功能,内置
。任何单极单掷(spst)开关,并在两个不同的燃油地图之间切换
.齿轮/速度输入允许根据齿轮调整地图
.指挥官v能够允许每个气缸单独映射,并为每个齿轮连接齿轮位置输入
。
.增强的'加速泵'功能
.用于越野车和ATV,请参见相应的目录下的moose power commanders
.制造。在美国,
二级燃油模块
允许在8个喷油器的自行车上使用dynojet快速换挡传感器,这提供了额外的燃油消耗。有了燃油控制和换档功能
如果档位输入连接到你的PCV,你可以在 "每档 "的基础上调整所有的喷油器
。
此外,需要注意的是,单根电缆连接到pcv
。您还可以分别映射每个喷油器,为您提供多达48个完整的映射
。基本'模式允许你有一个单一的燃料表,简单地将所要求的燃料变化同时放在上部和下部喷油器模块中
。上下喷油器的调整幅度高达+250/-100%
"基本模式 "是需要更多燃料的改装发动机的完美设置。比四喷油器能提供的更多,但不需要分别映射每个气缸和每个档位的复杂性
快速换档扩展。qem允许dynojet快速换挡传感器与power commander v一起使用在有八个喷油器的自行车上
。附上你将拥有完整的快速换挡功能
.QEM连接到上部喷油器,然后进入PCV
.
・Fuel control for each individual cylinder in a smaller enclosure
・Warm-up" fuel adjustment (unit reads engine temp and allows fuel / timing adjustments based on the reading)
・Reduced size from the PCIII USB
・Easy to install
・USB powered from computer; 9 volt adapter is no longer needed
・Two-position map-switching function built in
・It can add any Single Pole Single Throw (SPST) switch and toggle between two different fuel maps
・Gear / speed input allows for map adjustment based on gear
・Analog input allows user to install any 0-5 volt sensor
・Build an adjustment table based on analog input such as boost or temperature
・Power Commander V is capable of allowing each cylinder to be mapped individually and for each gear with the gear position input connected
・More tuning ranges than PCIII USB
・Enhanced “accel pump" utility
・For Offroad and ATV, see appropriate catalog under Moose Power Commanders
・Made in the U.S.A.
SECONDARY FUEL MODULE
・Allows for the use of the Dynojet Quick Shifter sensor on eight-injector bikes which provides added fuel control and shifter functionality
・If gear position input is connected to your PCV, you can adjust all of the injectors on a “per gear" basis
・Allows for the adjustment of all eight-injectors
・See application chart for availability
・Single cable connection to the PCV
・Connects to the upper injector rail using OEM connectors
・You can also map each injector separately, giving you up to 48 complete maps
・The “basic" mode allows you to have a single fuel table that simply puts the requested fuel change in both upper and lower injector modules at the same time
・Adjust both upper and lower injectors by as much as +250 / -100%
・The “basic" mode is the perfect setting for modified engines that require more fuel than four-injectors can provide, but do not need the complexity of mapping each cylinder and each gear separately
QUICK SHIFTER EXPANSION MODULE
・The QEM allows the Dynojet Quick Shifter sensor to be used with Power Commander V on bikes that have eight injectors
・Once the sensor is attached you will have full Quick Shifter functionality
・The QEM connects to the upper injectors and then into the PCV
[Translation]
・Fuel control for each individual cylinder in a small enclosure
・Warm-up fuel adjustment (a unit that reads engine temperature and allows fuel / timing adjustments based on the reading)
・Size reduction from PCIII USB
・Easy to install
・USB supplied from computer; 9 volt adapter is no longer needed
・Built-in 2-position map switching function
・Single Pole Single Throw (SPST) switch is added to switch between two different fuel maps
・Gear / speed input enables gear-based map adjustment
・Using analog inputs, 0-5V sensors can be installed
・Create an adjustment table based on analog inputs such as boost or temperature
・The Power Commander V can map each cylinder individually.
・More tuning range than PCIII USB
・Enhanced "acceleration pump" utility
・For Offroad and ATV, please refer to the appropriate Moose Power Commanders catalog.
・Made in USA
Secondary Fuel Module
・Dynojet Quick Shifter Sensor can be used on 8 injector bikes to provide additional fuel control and shifter function
・If the gear position input is connected to the PCV, all injectors can be adjusted in "gear units"
・All 8 injectors can be adjusted
・See the available application charts
・Single cable connection to PCV
・Connect to the upper injector rail using the OEM connector
・Each injector can be mapped separately to complete a map of up to 48 injectors
・In the "Basic" mode, a single fuel table can be prepared that will feed the requested fuel change to both the upper and lower injector modules simultaneously
・Up / Down Injector + 250 / -100
・The "basic" mode is the perfect setting for a modified engine that requires more fuel than four injectors, but does not require the complexity of mapping each cylinder and each gear separately
QUICK SHIFTER EXPANSION MODULE
・The QEM allows the Dynojet quickshifter sensor to be used with the Power Commander V on motorcycles with eight injectors
・Once the sensor is installed, the full functionality of the Quick Shifter can be used
・QEM is connected to the upper injector, and then to the PCV