12V摩托车用
发光色:白色
6000K DC点灯方式
车检标准合格(25000 Candela)
额定电压:DC12V
消耗电力:远光20W/近光20W
LED:CREE制 X Lamp XP-L LEDs
色温:6000K
按照说明书正确安装。不正确的安装将导致火灾。它可能会导致故障。
※在安装前,请务必取下电池负极侧的端子线,并确认钥匙已关闭。<请勿触摸或玷污LED芯片。LED灯泡有一个带密封圈的亚克力帽。拆除盖子和密封圈后,因污染而造成的LED灯泡损坏不在保修范围内。
※本产品为精密仪器,操作时应十分小心。不要摔倒或强行拉线。操作不当可能会造成故障、受伤或烧伤,并可能导致危及生命的事故。此外,要小心,因为火花和有缺陷的绝缘材料会引起故障和车辆火灾。<本产品的拆解。不要对数据进行任何修改。分解:我们对改装后的产品不提供任何保证。<不要直视大灯的LED灯。它可能会导致视觉障碍。<在关灯期间和关灯后,请勿将水溅到镜头上。温度的突然变化可能会导致透镜或LED灯泡的损坏。不要触摸 "导阀体"、后风扇安装架或控制器单元,因为它们可能会变热。
※本产品仅供摩托车使用,不能用于四轮车。<请勿用纸或布覆盖,也不要在易燃物附近点燃。它可能会引起火灾或异常加热。请勿在易燃物附近点燃,如易燃喷漆稀释剂或其他可能点燃的易燃物。<请勿在点亮状态下安装大灯。否则可能导致故障或烧毁。
※本产品为日常使用的防水产品,但并非完全防水。用乙烯胶带或自粘胶带将控制器单元耦合器包起来,或用填缝剂防水。不要用超过必要的水润湿它。
※用高压清洗机洗车时,不要让高压清洗直接撞击产品。<请勿跌落或强烈撞击LED灯泡或控制单元。不仅会损害或降低性能,还可能造成伤害。
*当组装LED灯泡时,请务必将附带的硅脂涂抹在 "用户手册 "中的油脂标记处。<不要遮住防水扇。确保风扇后面有足够的空间让空气流动。<使用螺纹锁固剂,防止螺纹部位的松动。另外,请定期重新拧紧。
※安装需要专业的知识和技能。请到指定的维修机构,由熟练的技师进行维修。
※使用前对准光轴。它可能会阻碍对向车辆的视线,造成交通事故。详情请参考《道路车辆安全标准》。
*因使用本产品而引起的故障。因意外事故造成的损失,本公司不承担任何责任。同时,本公司不承担因维修产品而产生的任何维修费用或其他费用。先谢谢你的理解。
*如果您在安装或使用过程中感觉到任何问题,请联系您的经销商或本公司服务部。
For 12V motorcycles
Luminescence Color: white
6000 Kelvin DC lighting system
Rated Voltage: DC12V
Power consumption: Hi beam 20W / Lo beam 20W
LED: CREE XLamp XP-L LEDs
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.The LED bulb comes with an acrylic cap with a sealing seal.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*When assembling the LED bulb, be sure to apply the supplied silicon grease to the areas indicated by the grease marks in the instruction manual.
*Do not cover up the waterproof fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*Neo Factory will not be held responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact your dealer or PROTEC service department.