材料:铝
套装内容
宽摆臂(不含摇杆+16厘米)
,3件式10英寸5.5j轮毂
,宽大的枢纽
,制动系统
,驱动链轮偏移系统
,宽大的悬挂式吊架
[关于安装
该套件不包括用于固定后制动主缸的支架。请单独准备。驱动链轮偏移套件要求发电机盖的链轮部分被加工掉。另外,该套件与日本和隆鑫的发动机兼容,但一些中国发动机,如力帆150cc,可能无法在四点上得到支持。
为Monkey使用420尺寸的前后链轮。包括组装的说明。请参考说明书,仔细组装。然而,维修工作的常识性技术在说明书中没有描述。装配工作只能由在摩托车维修方面有经验的人进行。传动链前端的数量取决于客户的车辆状况和前后链轮,并且不由gm-moto提供。
在骑行前一定要检查后悬架是否有任何异常接触点,即使后悬架处于全底状态。如果你的车架和该摆臂之间的间隙每边超过0.5毫米,请使用垫圈或其他方法来减少间隙。如果以较大的间隙拧紧枢轴,摆臂将承受高负荷,在最坏的情况下可能会被损坏。开始骑行后,要注意所谓的 "初始松动 "的发生,要经常进行检查,避免出现意外问题。
请注意,该产品是在海外制造的,可能没有其他产品做得那么好。由于运输问题,可能有一些轻微的划痕和擦伤。
*由于规格的变化,链条调节器和支架钩已从金色变为钛色。
请注意,由于制造商的原因,产品规格可能会有变化。请理解。
Material: Aluminum
[Kit Contents]
・Wide swingarm (without stabilizer +16cm)
・3-piece 10-inch 5.5J wheels
・Wide hub
・Brake system
・Drive sprocket offset system
・Wide suspension hanger
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
[About the installation]
The rear brake master cylinder fixing bracket is not included in the kit.Please prepare separately.The drive sprocket offset kit requires the sprocket section of the generator cover to be cut off.However, some Chinese engines such as Lifan 150cc may not be able to support 4 points.
Please use the 420 size sprockets for Monkey.Assembly instructions will be included.Please refer to the instruction manual and assemble carefully.However, common sense techniques for maintenance work are not described in the manual.Experienced motorcycle mechanics are required to perform the assembly work.The number of frames of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
Even when the rear suspension is at full bottom, be sure to check for any abnormal contact points before driving.If there is a gap of 0.5mm or more between the frame and the swingarm, please use washers to reduce the gap.If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.After the start of driving, pay attention to the occurrence of so-called "initial loosening" and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
※The chain adjuster and the stand hook have been changed from gold to titanium color.
*There may be changes in product specifications due to the manufacturer's reasons.