I ordered Steel. Ideal for loading of sorting Bag and Camping touring. Since it was imported from Thailand, there was a missing item of a few scratches and parts without Instruction Manual etc, but it was good as it corresponded. The price is cheap and it is a product as expected..
Weight is Quantity:The set has 7 kilos Because this rack is terribly firm, and this rack is in a state of large strange heavy from the luggage, always installation is I think about it That said, you can't take it off only when you use it View Detail
Install a day pack or RainBack for everyday use, or anything else that fits the weather and where you're going It is ideal for day trips and overnight tours in the woods because it can be made and the center of gravity is kept low Of course, during long touring, the maximum load capacity can be reached No problems with the construction and strength, it's a great cosmetic product! View Detail
I have Aluminum and Steel but this time I purchased Aluminum. It is awkward anyhow. It's a big deal.. I can forgive you because I like it. Although there is no description of allowable weight, it seems to be sturdy looking so it seems to be loaded for various reasons for the time being. Of course, since there is no Manual etc attached, it is the installation while looking at the picture of Site. Although it is not difficult, some power work is necessary. View Detail
I installed it on my 21CRF250L. I considered other products, but chose this one because I had previously purchased this manufacturer's Under Guard and was satisfied with the quality. It is cosmetically better than similar products, and it is stiff enough to withstand hard falls on forest roads.
However, the length of the front bushing (the silver colored tube in the photo) is a little short, probably because it is for the 300L. Therefore, if nothing is applied, the bushing will float and the stress will be concentrated at the base of the bolt. So, I used an M8×18Washer to apply tension to the bushing. Now there is no strength problem. (I put two 1.6mm thick sheets on each side and it was just right.)
I hope this will be helpful to those who have been hesitant to buy the product due to lack of reviews.View Detail
I bought this because I'm not a fan of top cases that look like a motorcycle delivery service, and since I'll only be riding alone anyway, I wanted to attach a small bag to the tandem seat area. It's easy to install, and it transforms the tiny tandem seat of the TENERE into a wide, flat cargo bed, and the rack covers the panel behind the tandem seat, right above the stop-lamp. The steel plate is thick, and it doesn't feel like a pela at all.
This rack is the middle and Quantity:Pair (for Left and Right) It consists of three Parts, Quantity:Pair (for Left and Right) You can also choose not to install the Fender panel. However, the upper half of the yamaha logo will be hidden, so if you don't want to add a Saddle Bag, you can use only the middle cargo bed Parts.
The only disadvantage of this rack is, of course, that it makes it impossible to remove the tandem seat. For example, if you have an ETC device under the tandem seat, it will be very troublesome to insert and remove the ETC card. However, if you don't want to give up the removal of the tandem seat, you may want to use a cargo rack like TourerTEC's Luggage Rack, which can be installed using the mounting mechanism of the tandem seat. However, if you don't want to give up the removal of the Tandem seat, you may want to consider a cargo rack like the TourerTEC Luggage Rack, which uses the Tandem seat mounting mechanism. However, in terms of mounting strength, this product seems to be stronger, as it uses four bolts to attach it firmly.
In general, it is a good simple and sturdy cargo carrier.View Detail
I was looking for a Support bar to install a Side Back. I was going to go with the DRC 16mm PipeSpec. New ModelRALLY50MD47 was still under development. So, Carrier and Side Back SupportParts that are compatible with MD47 from SRC. When I found out that a new product was released, I saw that it was cool and I wanted to have it. ...... And before I knew it, I was snapping away. The item was shipped overseas and the delivery date was two months away. I received it in about two weeks, quite a bit ahead of schedule. Checked the actual item early on. Packaging is fine. I think the welds are acceptable, no distortions. One point, there was a mark like the tip of the Drill hit, and only there was chipped and peeled. If you're nervous, I'd return it. We were able to finish the installation on the body smoothly without any difficulty. M5×15 bolts are used to connect Carrier and both SIDE parts.:Pair (for Left and Right) I use 8 of them together. Because the attachment was M5×15mm, I thought Screw was a little short, so I changed it to 20mm Screw. Just to be safe, I applied a light coat of Locktite loosener to the Bolt. Also, if a few of these 8 pieces fall out, the Side PartsBody will still be on the MotorcycleBody hook bolt. I don't think you have to worry about it coming off directly because it's fixed. The wide Carrier in board form becomes an occasional Table and (See photo) Quantity:Pair (for Left and Right) The Side Back SupportParts that protrude into the It looks like an AdventureMotorcycle. The OilTank set is designed to install a Sub tank. I installed a Hard case there. (Mine is a Carrier set, no Tank). I use it to store tools and equipment. This also plays a role in producing a powerful effect. It gives a sense of weight to the scantily clad Rear. (See photo) 3mm aluminum seems to be strong enough. The Side Back SupportParts part is honestly not as good as DRC's 16 pie PipeSpec. This one is a board composite and seems a little poor, doesn't it? Well, I'll check the durability from now on. Finally, can I use the OEM Helmet holder? I checked it with HelmetL Size of WINS X-ROAD FREE RIDE. (M Size is also the same size as L?). LimitIt did not arrive. (See photo)View Detail
The Off car has a thin Seat and can't carry luggage. That said, TOP-BOX hates Parenthesis. SIDEPannier I don't have as much luggage as I always put on, and more importantly, it's expensive. Most of the rear carriers are also small so as not to kill the Tandem seat. I want to put an ENDURISTAN Rally pack on it, but I don't want to make a hole in it. So, this SRC rack will solve everything. The price isn't cheap, but it's one of the cheapest I've seen other products. The texture is good and the installation is easy.
Quantity:The first picture shows a regular Waist Bag mounted on the rack. The second one is with DryPack and Rubber net. In the future, we plan to add a bottle holder, etc. to the overhang on the side.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail