87.82 RMB
(1,839 日元)
80.18~ RMB
(1,679 日元)
(
9% 折扣
)
4 (6 评论)
Very Good
I purchased a Φ58 NOJIMA Full Exhaust.
It's stable, and unlike standard stainless steel baffles, it doesn't make a beating noise.
I measured the sound at 3000rpm (above the rear cowl)
*Without Baffle 93dB
*With Baffle 90dB
I purchased a Φ58 NOJIMA Full Exhaust.
It's stable, and unlike standard stainless steel baffles, it doesn't make a beating noise.
I measured the sound at 3000rpm (above the rear cowl)
*Without Baffle 93dB
*With Baffle 90dB
It cuts the bass sound.
With this volume, it'll be okay idling in the neighborhood.
Reviews For CF POSH 消音器用 铝合金切削加工挡板 From Other Webike User
Average
no problemI used it on the AKRAPOVICSilencer in HUSQVARNA.
I pulled out the OEM Baffle and installed it.
Size is exactly as shown and there is not much to say about the performance etc.
The sound is quieter now that the diameter has been reduced to Small.View Detail
Excellent
MORIWAKIZEROTitanium ExhaustCB 1300 SF, MORIWAKIZEROTITHIRANE EXHUST
Exhaust End is less than 52 mm. There was one who attached 51 mm when examining with Net, 52 mm was chosen as a bad source from writing that it was good even 52 mm because there is a little gap.
So, when I tried on it, I can not get into it. Thin skin Quantity : 1pc. As it seems good to peel off, I decided to shave the surface lightly with Thunder.
As the sound became Large, I installed End Baffle, but the volume dropped as expected.
Sound quality is not a problem. I was thinking about returning to NORMAL.
Products can be selected in 1 mm increments.
I am very satisfied..
View Detail
Excellent
Will you install it on Tel MINI-Nyo?The TEL MINI-Nyo Exhaust System that is attached now is without Baffle, so it sounds pretty good.
I do not think that I will not run with Baffle installed,
I bought it for the vehicle inspection. (It is still a while)
For the time being, we are planning to measure the volume by wearing it on a trial.View Detail
Very Good
During MaintenanceThere is a case to put Engine on Maintenance of cbr 1000rr. Oil exchange etc..
At that time I purchased it because it becomes a trouble of the neighbors.
The inner diameter of Baffle is also 22 mm Meter and Small, so the volume has also dropped greatly.
Still I still use my mind, but I got better at all..
Especially, there is no reason for choosing Posh, but if it says so, I thought desorption would be easy as Baffle itself had Screw cut off.View Detail
Most Viewed Reviews Of CF POSH Baffle / Inner Silencer
Excellent
For muffling.I bought and installed this product in hopes of muffling the noise of the Exhaust System.
It works, and I'm satisfied that the volume is as low as I can allow it to be.
It's also good that it doesn't spoil the appearance at all. (To be installed inside the space between the middle pipe and the silencer)
By the way, it's not Normal muffler.View Detail
Very Good
For securing exhaust pressure[Car body] 06 CB400SF Vtec3
The silencer of SP Tadao's Full Exhaust System was replaced with UCP's Universal Silencer.
The Baffle that came with it was too loose and the exhaust sound cracked in the normal use range of 4,000 to 5,500 RPM.
Daytona, CFPosh, and NPROject's Baffle were purchased and replaced. The DAYTONA Baffle with the narrowest exhaust port is better, but the sound is still a little cracked and the torque is not as good as it should be.
So I bought this product hoping to improve the sound deadening and exhaust pressure.
Installation is easy if you have the basic tools and a Skill to remove the Silencer.
I thought there might be a rattling sound because I installed it between Silencer and Exhaust pipe, so I installed it after applying Liquid Gasket thinly. Thanks to that, there is no rattling sound and no exhaust leak.
The product is very accurate and the construction is beautiful. You can't see it once it's installed, but...
The cracking of the exhaust sound that was a problem is gone and the exhaust pressure has been set to a good level.
If you have a silencer that is too loose, or if you can't get by with End Baffle, this is the product for you.View Detail
Average
no problemI used it on the AKRAPOVICSilencer in HUSQVARNA.
I pulled out the OEM Baffle and installed it.
Size is exactly as shown and there is not much to say about the performance etc.
The sound is quieter now that the diameter has been reduced to Small.View Detail
Excellent
MORIWAKIZEROTitanium ExhaustCB 1300 SF, MORIWAKIZEROTITHIRANE EXHUST
Exhaust End is less than 52 mm. There was one who attached 51 mm when examining with Net, 52 mm was chosen as a bad source from writing that it was good even 52 mm because there is a little gap.
So, when I tried on it, I can not get into it. Thin skin Quantity : 1pc. As it seems good to peel off, I decided to shave the surface lightly with Thunder.
As the sound became Large, I installed End Baffle, but the volume dropped as expected.
Sound quality is not a problem. I was thinking about returning to NORMAL.
Products can be selected in 1 mm increments.
I am very satisfied..
View Detail
Excellent
It got quiet and slow Torque also increased!【What made you decide the purchase?】
I was looking for an Inner baffle to put in between the intermediate Pipe and the Silencer thought that I wanted to suppress the volume a little more. Just the outer diameter Size : 60. 5 mm is Exactly and inner diameter is also desired Size : I bought it because it was 30 mm and the price was reasonable.
【How was it actually used?】
Try Engine.. Idling does not change so much volume. But burst sound was reduced and the sound quality which Kado was able to be taken. When going to trial run the engine turns up, I feel a little quieter than before. Engine noise became more concerned than exhaust noise.
【Was the installation difficult? (Hard parts case)
It was very simple.. In my case, I removed Silencer with one Bolt and one Spring and attached Inner baffle between Intermediate Pipe and Silencer.
【Please tell me the point of installation and hang (in the case of Hard parts)】
It is to point the Pipe side protruding from the Inner baffle to the Engine side.
[Is there anything I was disappointed about?]
Nothing in particular.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Nothing in particular. I think that it is a good product.
【Have you compared items?】
Inner baffle of Size I want is not found by other companies.
[Others]
In my car case, not only the sound became quiet but also Torque increased in the low rotation range of 2000 to 3000 rpm. It became easy to start with the departure and city ride.
There is no Custom feeling because it does not change appearance, but it seems that you can run Gentle with this.View Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail